IPv6 (tutorial) IPv6 (教程) I cont. IPv6 on v24; IPv6 setup Hurricane Electric Tunnel Broker; IPv6 startup script; I cont. IPv6, 6in4 tunnel - GUI only; L. Linux IPv6 Router Advertisement Daemon (radvd)

May 04, 2016 · Most routers provide pretty good IPv6 support at this point but unfortunately, there are exceptions. Notably, I was surprised to learn that DD-WRT IPv6 configuration was ridiculously complex, and I didn’t feel bold enough to try to enable it. I’m hoping that DD-WRT can work to improve this in the future. Trying it out Jul 13, 2009 · Next, you’ll need a version of DD-WRT that supports IPv6. I’ve had good luck with v2.3 SP2, so that’s what I’m going to recommend. Before you can install the DD-WRT standard image, however, we must first upgrade the WAP to a DD-WRT standard mini image from the standard Linksys firmware upgrade page in the WAP’s web interface. Jan 23, 2011 · DD-WRT IPv6 to Your Local Network Last time I showed you how to get a dynamic tunnel from SixXs to a DD-WRT router. This time, we're going to get Router Advertisment going, the simplest way to distribute a routed subnet to your network. Forum discussion: I am new to Charter (Spectrum) and am unsure which settings will enable IPv6. I seem to have the standard 3 choices (as seen in screenshot) Native IPv6 from ISP DHCPv6 with According to all sources, enabling IPv6 doesn’t load the IPv6 module, and enabling Radvd doesn’t guarantee that it will start. There exist detailed descriptions on how to get it working: (1) IPv6 on v24, (2) Native IPv6 in dd-wrt (detailing 4 years of efforts!), (3) DD-WRT IPv6 (tutorial). The DD-WRT Command Line. aka the DD-WRT Linux shell. This is an 'ash' shell. Ash is a version of sh, literally 'A SHell' (A command Interpreter) Basic Syntax. The Linux Command Shell (Ash) is not the same as the Windows/DOS command prompt. / (and not \) is used to separate directories in a path, just like the interweb. Note: in AP mode, LAN cable to gateway/modem and LAN cable to IPTV box must be on the switch ports of the dd-wrt router and not on the WAN port, even if "assign WAN port to switch" is enabled. Tested on Linksys EA2700 (build 38581), Netgear R7000, Netgear R7000P. ARM Kong builds 35550M and 38580M. Do not consider these build recommendations.

2) Once it is hooked and DD-WRT wants to restart dnsmasq the script is executed instead, and adds some lines to the generated /etc/hosts afterwards it executes the real dnsmasq. Finally it reinstalls the wrapper. You have to place the script somewhere and put it in to list of commands executed at bootup. Then adjust the variables at the setup

Hi, In the recent beta version r42366 (02-14-2020), the dnsmasq service stops offering dhcp for clients if the wan has IPv6 (DHCPv6 whit prefix delegation), note that it stops responding once you opt for the WAN IPv6 (PPPoE) ) and does not work until you enter by telnet to restart the dnsmasq service.. I also tested it with an equal PPPoE WAN connection without IPv6 support and the problem did IPTV - blocking multicast on WIFI - DD-WRT Wiki Note: in AP mode, LAN cable to gateway/modem and LAN cable to IPTV box must be on the switch ports of the dd-wrt router and not on the WAN port, even if "assign WAN port to switch" is enabled. Tested on Linksys EA2700 (build 38581), Netgear R7000, Netgear R7000P. ARM Kong builds 35550M and 38580M. Do not consider these build recommendations. How to configure IPv6 connectivity with Tunnel Broker

Sep 28, 2011 · DD-WRT has native IPv6 functionality, as well as the 6to4 [8] address-translation system. Quality-of-service controls. Most routers have some basic QoS management, but some of the DD-WRT builds

Sep 28, 2018 Andee's Hacks: DD-WRT IPv6 to Your Local Network